RUENUZЎЗ

Engineering Center

Research, development and preparation of polymer solutions

MechanicalRheologyThermalChemicalOpticalSurfacePilot Extrusion TP

TP-LAB

Engineering center for polymer materials research and development.

TP-LAB combines laboratory research, formulation development, production of experimental samples and technological support. We study polymer raw materials, masterbatches, compounds and finished products, identify the causes of deviations and production defects, select components and develop formulations with consideration for the requirements of the material, finished product and processing technology.

The center’s capabilities cover the entire path from task definition and comparative evaluation of materials to sample production, verification of their characteristics and preparation for industrial implementation. The client receives test results, technical conclusions and recommendations for material selection, formulation adjustment, defect elimination and improved production stability.
Technoplastic TP-LAB laboratory

Testing areas

We determine the key characteristics of polymer raw materials, masterbatches, compounds and finished products.

We perform analytical, physical, rheological, mechanical, thermal, optical, climatic and technological testing of polymer materials. The research programme is defined with consideration for the material type, processing technology, production task and requirements for the finished product.

The results are used for incoming raw-material control, comparative evaluation of materials, identification of the causes of deviations, formulation verification and assessment of compliance with specified requirements.

Review the available tests, methods used and service pricing.
016 parameters

Physical properties

Density, moisture, water absorption and other physical parameters.

025 parameters

Rheological properties

Melt flow rate indicators MFR and MVR.

039 parameters

Mechanical properties

Tensile, flexural, elastic modulus and impact strength properties.

04

Material hardness

Shore A and D hardness, as well as pencil hardness of the surface.

058 parameters

Thermal properties

HDT, Vicat, melting, crystallization and thermal stability.

068 parameters

Optical and color properties

Transparency, haze, gloss, L*a*b* coordinates and color difference ΔE.

077 parameters

Film and surface properties

Coefficient of friction, blocking, opening behavior and surface characteristics.

087 studies

Analytical studies

Polymer identification and analysis of material composition, structure and thermal behavior.

09

Weathering resistance

Changes in properties and appearance after UV and climatic exposure.

105 areas

Flammability and electrical properties

Flammability, behavior under ignition source exposure and electrical characteristics.

Engineering solutions

We select existing grades and develop custom formulations with laboratory verification of properties and processability.

Based on the technical specification, we select an existing grade or develop a custom formulation for a colour, functional or processing masterbatch, mineral concentrate or engineering polymer compound.

To verify the developed formulation, we produce experimental material, prepare moulded or film specimens and perform comparative tests under controlled conditions.

Based on the results, we adjust the formulation, evaluate the effect of components on material properties and processability, and prepare the material for subsequent production trials.
Compounded pellets
01

Compounded pellets

Experimental masterbatch and polymer compound batches for further processing and testing.

Moulded specimens
02

Moulded specimens

Standard and technical specimens for mechanical, thermal, colour and performance evaluation.

Film samples
03

Film samples

Film for processability, COF, blocking, opening, optical and surface property assessment.

Pilot batch
04

Pilot batch

We produce material in the agreed volume for extended testing, assessment of formulation reproducibility and preparation for production trials.

TP-LAB equipment

Instruments and processing units for sample preparation, testing and analysis of polymer materials.

TP-LAB equipment enables the preparation of experimental formulations, production of specimens, instrumental analysis and determination of key characteristics of polymer materials.

The equipment is organised by research area. Select the required section to view the instruments, measured characteristics and test methods used.
Automatic Densitometer HR-250AZG
Physical propertiesTP-LAB

Automatic Densitometer HR-250AZG

ManufacturerA&D Company Ltd
Country of originJapan
Purpose

Determination of physical characteristics of polymer materials.

What it determines
  • Density
  • specific gravity
Key parameters
Densityspecific gravitybulk density
Applicable standards
ASTMASTM D792, D1505ISO / IECISO 1183ГОСТ / DINГОСТ 15139, ГОСТ 18995.1
Typical tasks

Quality control; formulation development; comparative analysis; deviation analysis.

Send request ↗
MS-70 Moisture Analyzer
Physical propertiesTP-LAB

MS-70 Moisture Analyzer

ManufacturerA&D Company Ltd
Country of originJapan
Purpose

Determination of physical characteristics of polymer materials.

What it determines
  • Moisture
Key parameters
Moisture content
Applicable standards
ASTMASTM D6980, D2216ISO / IECISO 15512ГОСТ / DINГОСТ 5180
Typical tasks

Quality control; formulation development; comparative analysis; deviation analysis.

Send request ↗
Hardness Tester DTR-300N
Mechanical propertiesTP-LAB

Hardness Tester DTR-300N

ManufacturerDAEKYUNG TECH & TESTERS
Country of originRepublic of Korea
Purpose

Assessment of mechanical characteristics and material behaviour under load.

What it determines
  • Shore hardness
Key parameters
Shore AShore D
Applicable standards
ASTMASTM D2240ISO / IECISO 7619, ISO 868ГОСТ / DINГОСТ 263
Typical tasks

Quality control; formulation development; comparative analysis; deviation analysis.

Send request ↗
Universal Testing Machine QM100T
Mechanical propertiesTP-LAB

Universal Testing Machine QM100T

ManufacturerQMESYS
Country of originRepublic of Korea
Purpose

Assessment of mechanical characteristics and material behaviour under load.

What it determines
  • Strength and deformation
Key parameters
Tensile strengthmoduluselongationcompressive strength
Applicable standards
ASTMASTM D638, ASTM D695ISO / IECISO 527, ISO 604ГОСТ / DINГОСТ 11262, ГОСТ 4651
Typical tasks

Quality control; formulation development; comparative analysis; deviation analysis.

Send request ↗
Digital Shore Hardness Durometer
Mechanical propertiesTP-LAB

Digital Shore Hardness Durometer

ManufacturerDeFelsko
Country of originUSA
Purpose

Assessment of mechanical characteristics and material behaviour under load.

What it determines
  • Hardness
Key parameters
Shore AShore D
Applicable standards
ASTMASTM D2240ISO / IECISO 7619, ISO 868ГОСТ / DINГОСТ 263
Typical tasks

Quality control; formulation development; comparative analysis; deviation analysis.

Send request ↗
Impact Tester QM700L
Mechanical propertiesTP-LAB

Impact Tester QM700L

ManufacturerQMESYS
Country of originRepublic of Korea
Purpose

Assessment of mechanical characteristics and material behaviour under load.

What it determines
  • Impact strength
Key parameters
IzodCharpy
Applicable standards
ASTMASTM D256, ASTM D6110ISO / IECISO 179, ISO 180ГОСТ / DINГОСТ 4647, ГОСТ 19109
Typical tasks

Quality control; formulation development; comparative analysis; deviation analysis.

Send request ↗
Column Frame 2 kN
Mechanical propertiesTP-LAB

Column Frame 2 kN

ManufacturerQMESYS
Country of originRepublic of Korea
Purpose

Evaluation of mechanical properties and material behaviour under load.

What it determines
  • Film blocking
Key parameters
Film separation force
Applicable standards
ASTMASTM D3354
Typical tasks

Quality control; formulation development; comparative analysis; deviation analysis.

Send request ↗
Auto Pencil Hardness Tester QM450A
Mechanical propertiesTP-LAB

Auto Pencil Hardness Tester QM450A

ManufacturerQMESYS
Country of originRepublic of Korea
Purpose

Evaluation of mechanical properties and material behaviour under load.

What it determines
  • Coating hardness
Key parameters
Pencil hardness
Applicable standards
ASTMASTM D3363ISO / IECISO 15184
Typical tasks

Quality control; formulation development; comparative analysis; deviation analysis.

Send request ↗
Glow Wire Tester
Thermal propertiesTP-LAB

Glow Wire Tester

ManufacturerQMESYS
Country of originRepublic of Korea
Purpose

Assessment of material behaviour under thermal exposure.

What it determines
  • Glow-wire resistance
Key parameters
Glow Wire Temperature (GWIT)Glow Wire Flammability (GWFI)
Applicable standards
ASTMASTM D6194ISO / IECIEC 60695-2-10ГОСТ / DINГОСТ IEC 60695
Typical tasks

Quality control; formulation development; comparative analysis; deviation analysis.

Send request ↗
Furnace QM1270
Thermal propertiesTP-LAB

Furnace QM1270

ManufacturerQMESYS
Country of originRepublic of Korea
Purpose

Assessment of material behaviour under thermal exposure.

What it determines
  • Ash content
Key parameters
Ash contentfiller content
Applicable standards
ASTMASTM D5630ISO / IECISO 3451ГОСТ / DINГОСТ 27037
Typical tasks

Quality control; formulation development; comparative analysis; deviation analysis.

Send request ↗
Mini Heating Plate QM900MH
Thermal propertiesTP-LAB

Mini Heating Plate QM900MH

ManufacturerQMESYS
Country of originRepublic of Korea
Purpose

Assessment of material behaviour under thermal exposure.

What it determines
  • Vicat softening temperature
Key parameters
Vicat Softening Temperature
Applicable standards
ASTMASTM D1525ISO / IECISO 306ГОСТ / DINГОСТ 15088
Typical tasks

Quality control; formulation development; comparative analysis; deviation analysis.

Send request ↗
Heat Distortion Temperature Tester QM950H
Thermal propertiesTP-LAB

Heat Distortion Temperature Tester QM950H

ManufacturerQMESYS
Country of originRepublic of Korea
Purpose

Assessment of material behaviour under thermal exposure.

What it determines
  • Heat deflection temperature
Key parameters
HDT
Applicable standards
ASTMASTM D648ISO / IECISO 75ГОСТ / DINГОСТ 15065
Typical tasks

Quality control; formulation development; comparative analysis; deviation analysis.

Send request ↗
Automatic Melt Flow Indexer QM280A
Rheological propertiesTP-LAB

Automatic Melt Flow Indexer QM280A

ManufacturerQMESYS
Country of originRepublic of Korea
Purpose

Determination of melt rheological characteristics and processability.

What it determines
  • Melt flow
Key parameters
MFRMFIMVR
Applicable standards
ASTMASTM D1238ISO / IECISO 1133ГОСТ / DINГОСТ 11645
Typical tasks

Quality control; formulation development; comparative analysis; deviation analysis.

Send request ↗
UL-94 Flammability Tester QM500U
Flammability testingTP-LAB

UL-94 Flammability Tester QM500U

ManufacturerQMESYS
Country of originRepublic of Korea
Purpose

Assessment of flammability and material behaviour under flame exposure.

What it determines
  • Flammability
Key parameters
UL94 HBV2V1V0
Applicable standards
ASTMASTM D3801, UL94ISO / IECIEC 60695ГОСТ / DINГОСТ 12.1.044
Typical tasks

Quality control; formulation development; comparative analysis; deviation analysis.

Send request ↗
UV Weathering Chamber UV600
Weathering testingTP-LAB

UV Weathering Chamber UV600

ManufacturerSANWOOD
Country of originChina
Purpose

Accelerated assessment of material resistance to UV and climatic ageing.

What it determines
  • UV resistance
Key parameters
Colour fastnessageingdegradation
Applicable standards
ASTMASTM G154, ASTM D4329ISO / IECISO 4892-3ГОСТ / DINГОСТ 9.803
Typical tasks

Quality control; formulation development; comparative analysis; deviation analysis.

Send request ↗
DSC 200
Thermal analysisTP-LAB

DSC 200

ManufacturerXiangYi
Country of originChina
Purpose

Investigation of thermal transitions, stability and material composition.

What it determines
  • Thermal properties
Key parameters
TmTcTgmelting enthalpy
Applicable standards
ASTMASTM E793, ASTM E794ISO / IECISO 11357ГОСТ / DINГОСТ 29122
Typical tasks

Quality control; formulation development; comparative analysis; deviation analysis.

Send request ↗
Pyris TGA 9
Thermal analysisTP-LAB

Pyris TGA 9

ManufacturerPerkinElmer
Country of originUnited Kingdom
Purpose

Investigation of thermal transitions, stability and material composition.

What it determines
  • Thermal stability
Key parameters
Decomposition temperaturefiller contentvolatile matter
Applicable standards
ASTMASTM E1131, ASTM D5630ISO / IECISO 9924-1
Typical tasks

Quality control; formulation development; comparative analysis; deviation analysis.

Send request ↗
FT-IR Spectrum Two
Chemical analysisTP-LAB

FT-IR Spectrum Two

ManufacturerPerkinElmer
Country of originUnited Kingdom
Purpose

Polymer identification and analysis of chemical characteristics.

What it determines
  • Material identification
Key parameters
Polymer typefunctional groupscontaminants
Applicable standards
ASTMASTM E1252, ASTM E168ISO / IECISO 4650ГОСТ / DINГОСТ 22091
Typical tasks

Quality control; formulation development; comparative analysis; deviation analysis.

Send request ↗
X-Rite Ci7860
Optical propertiesTP-LAB

X-Rite Ci7860

ManufacturerX-Rite
Country of originUSA
Purpose

Measurement of optical and colour characteristics.

What it determines
  • Colour characteristics
Key parameters
L*a*b*ΔEwhitenessyellowness
Applicable standards
ASTMASTM D2244, ASTM E1164ISO / IECISO 7724
Typical tasks

Quality control; formulation development; comparative analysis; deviation analysis.

Send request ↗
Laboratory Microscope
Optical propertiesTP-LAB

Laboratory Microscope

ManufacturerNingbo Yongxin
Country of originChina
Purpose

Measurement of optical and colour characteristics.

What it determines
  • Microstructure
Key parameters
Pigment dispersionfiller dispersionagglomerates
Applicable standards
Typical tasks

Quality control; formulation development; comparative analysis; deviation analysis.

Send request ↗
micro-TRI-gloss S
Optical propertiesTP-LAB

micro-TRI-gloss S

ManufacturerBYK
Country of originGermany
Purpose

Measurement of optical and colour characteristics.

What it determines
  • Surface gloss
Key parameters
Gloss 20°60°85°
Applicable standards
ASTMASTM D523ISO / IECISO 2813ГОСТ / DINDIN 67530
Typical tasks

Quality control; formulation development; comparative analysis; deviation analysis.

Send request ↗
COF Tester QM110CF
Surface propertiesTP-LAB

COF Tester QM110CF

ManufacturerQMESYS
Country of originRepublic of Korea
Purpose

Evaluation of surface and friction characteristics.

What it determines
  • Coefficient of friction
Key parameters
Static COFdynamic COF
Applicable standards
ASTMASTM D1894, ASTM D4917ISO / IECISO 8295
Typical tasks

Quality control; formulation development; comparative analysis; deviation analysis.

Send request ↗
Simco-Ion ST-4
Electrical propertiesTP-LAB

Simco-Ion ST-4

ManufacturerSimco
Country of originJapan
Purpose

Determination of electrical and antistatic properties.

What it determines
  • Antistatic properties
Key parameters
Surface resistancevolume resistance
Applicable standards
ASTMANSI/ESD STM11.11ISO / IECIEC 61340
Typical tasks

Quality control; formulation development; comparative analysis; deviation analysis.

Send request ↗

Work results

The scope of the result is determined by the task, research programme and agreed scope of work.

We provide data and technical conclusions to support an informed decision.
01

Task

Material, product or production problem.

02

Programme

We define the methods, samples and evaluation criteria.

03

Preparation

We prepare the material and the required specimens.

04

Testing

We perform measurements under controlled conditions.

05

Interpretation

We compare the results and identify the causes of deviations.

06

Result

We formulate conclusions and recommendations for the next step.

Need to study a material, develop a formulation or solve a production challenge?

TP-LAB specialists will review the input data and propose a programme of work.

Discuss the task ↗